How To Polish Silicon Wafers

Jun 07, 2024 Leave a message

Pre-Polishing Preparation

Before beginning the actual polishing process, there are several important preparatory steps:

Cleaning

Thoroughly clean the wafer surfaces to remove any residual particles or chemical residues from prior processes like lapping or etching. Contamination can lead to surface defects during polishing. We recommend cleaning via:

SC-1 clean - Hot ammonium hydroxide, hydrogen peroxide, and water in ratio of 1:1:5 at 75°C for 10 minutes

SC-2 clean - Hot hydrochloric acid, hydrogen peroxide, and water in ratio of 1:1:6 at 75°C for 10 minutes

Quick dump rinse (QDR) - Multiple baths of overflowing DI water for 2-3 minutes each

Inspection

Carefully inspect wafer surfaces after cleaning using brightfield mode to check for:

Residual particles or stains

Pits, scratches, or subsurface damage from prior processes

Other physical defects like edge chips/cracks

Address any issues at this stage before polishing to avoid exacerbating defects.

Apply Backing Layer

Apply an adhesive backing layer to the backside of the wafer to provide uniform support during polishing and prevent backside damage:

Apply 1-2 layers of UV curable adhesive

Ensure fully cured prior to polishing

Table 1. Recommended backing layers

Material Hardness Thickness Cure Time
PU Shore A 60 0.5mm 5 mins
Solgel Shore D 20 0.2mm 10 secs

Polishing Equipment

 

silicon wafers polishing

Key capabilities:

Variable spindle speeds up to 120 rpm

Programmable downforce/pressure up to 8 psi

Real-time torque monitoring

Automated slurry dispensing/feeding

Integrated post-polish cleaning stations

Polishing Process Steps

The main polishing steps are outlined below:

Prepare/Dress Polishing Pad

Select appropriate pad material (see recommendations later)

Condition new pads by diamond impregnating

Prior to each run, dress pad with diamond disc to refresh surface

Mount Wafer

Secure wafer firmly to wafer chuck/carrier

Center wafer properly to ensure uniform polishing

Set Process Parameters

Spindle speed - 30-60 rpm typical

Pressure - 3-5 psi typical

Slurry feed rate - 100-250 ml/min

Process duration - Dependent on material removal required

Begin Polishing Cycle

Start spindle rotation

Dispense slurry onto center of pad continuously

Lower wafer chuck and engage pad per set pressure

Monitor torque throughout process

Post-Polish Cleaning

Thorough cleaning after polishing is critical for removing residues and minimizing defects:

Primary clean - Brush scrub wafer surfaces with ammonium hydroxide or acetate based solutions

Secondary clean - Short dip in HF or other acid solutions to remove chemical residues

QDR - Multiple overflow baths for 3-5 minutes each

Inspect finished wafers again after cleaning. Rework/re-polish any necessary areas before proceeding to next process steps.

Silicon Wafer Polishing Process Optimization

Working At WaferPro

There are several key parameters that can be tuned to optimize the wafer polishing process:

Applied Downforce/Pressure

Higher pressure increases polishing/material removal rate

Too much pressure leads to edge rounding, microcracks

3-5 psi optimal for most applications

Rotation Speed

Increases temperature at pad-wafer interface

Higher speeds increase polishing rate up to a point

30-60 rpm suitable for most batch processes

Pad Materials

Selecting pad material impacts key factors like polishing rate, surface finish, and defect levels:

Table 2. Pad Material Comparisons

Pad Hardness Removal Rate Finish Defects Cost
Polyurethane Medium Medium Good Low Low
Polymer/Foam Soft Very High Rough High High
Non-woven Medium Low Excellent Very Low High

Softer pads cut faster but finish not as smooth

Hard pads slower polishing and higher burnishing

Multi-step processes ideal using harder final pad

Slurry Optimization

Balancing abrasive content/chemistry/pH/flow rate critical

Tailor slurry formulations to application and pad material

Continually test and improve our slurries for optimal results

 

Post-Polishing Analysis

Evaluating and analyzing post-polish wafer quality is imperative to ensure specifications are met and identify process improvements. Key analyses include:

Surface Roughness

Measure Ra, RMS, PSD, and HF data

Monitor long wavelength figure/flatness

Identify scratches, pits, particles, additional polishing needed

Film Thickness

Confirm removal of required thickness layer(s)

Check thickness uniformity across wafer surface

Haze Levels

Measure haze % and distribution

Ensure minimal residual surface damage per application specs

Defect Inspection

Use brightfield, darkfield, etc to reveal remaining defects

Compare pre and post polish defect levels/types

Feedback data to adjust pad, slurry, parameters

Our integrated metrology tools provide comprehensive analytical capabilities for optimal process control.

 

Surface Finish

Ra < 1 angstrom possible

RMS < 2 angstroms typical specification

Minimize microroughness through process optimization

Total Thickness Variation (TTV)

TTV < 1 um across wafer diameter readily attainable

TIR < 3 arc-sec over large optics feasible

Sub-nanometer thickness uniformity demonstrated

Defect Densities

Zero nano-scratches through pad conditioning, feed optimization

< 5 defects/cm^2 over large areas

Particle detection and minimization down to <0.1 um

Contact our engineering team to review your technical requirements and we will tailor a comprehensive polishing process to satisfy even the most stringent specifications.